PRODUCTS

  1. HOME
  2. PRODUCTS
  3. Precision Machine Tools
  4. Lineup

Precision Machine Tools

Lineup of Grinding Machine

Manual

Semi-Automatic

  • MSG-200H1
  • MSG-250H1
(Note)
The numeric affixed to the model code represents the amount of forward-and-backward shift.
However 46, 612, 614, 618 and 818 mean forward-and-backward and right-and-left shifts in “inch” . For example, 46 represents forward-and-backward shift by 4 inches and right-and-left shift by 6 inches.

MSG Series Option List

Magnet / Chuck control

1. Tilting electromagnetic chuck(250 x 120mm)
2. Tilting electromagnetic chuck(300 x 120mm)
3. Water-cooled tilting electromagnetic chuck (250 x 120mm)
4. Water-cooled tilting electromagnetic chuck (300 x 120mm)
5. Sine bar type electromagnetic chuck (270 x 125mm)
6. Water-cooled sine bar electromagnetic chuck (270 x 125mm)
7. Permanent sine bar chuck(240 x 125mm)
8. Permanent sine bar chuck(270 x 125mm)
9. Angular electromagnetic chuck(300 x 150mm)
10. Angular electromagnetic chuck(400 x 200mm)
11. Angular electromagnetic chuck(600 x 300mm)
12. Angular electromagnetic chuck(800 x 400mm)
13. Water-cooled angular electromagnetic chuck (300 x 150mm)
14. Water-cooled angular electromagnetic chuck (400 x 200mm)
15. Reversible switch
16. Manual controller
17. Mitsui Automatic chuck control MAG-81 (Max. x 0.5A)
18. Mitsui Automatic chuck control MAG-81A(Max. x 0.5A)
19. Mitsui Automatic chuck control MAG-300HP(Max. x 2.5A)
20. Cooling unit for water-cooled chuck
21. Demagnetizer (AC100V1A)

(Note) Type of suitable chuck differs depending on the type of objective machine.

Dust-collecting and water-supplying equipment

22. Dust catche*
23. Water-feeding unit**
24. Hood port
25. Dust catcher-water feeder**
26. Dust catcher-water feeder with 20L magnetic separator**
27. Water-feeding unit with 20L magnetic separator**
28. Water-feeding unit with 20L paper filter**
29. Sealing wet cover
30. Semi-Open type coolant enclosure

Other

31. Cross-Vertical Feed D.R.O D.R.O. = Digital Read Out
32. R-forming device
33. Angle-forming device
34. Top face parallel dresser
35. Diamond wheel dresser
36. Sine bar(100mm)
37. Balance bar & table
38. V-block(Max.25φclamp)
39. Square vice
40. Sine bar type square vice
41. Double-face dresser
42. Side dresser
43. Flange
44. Forming pointer(0.3R.1.0ct)
45. Diamond tool(1.0ct)
46. Diamond tool(0.5ct)
47. Special flange for small diameter grinding stone
48. Dial gauge stand (with 0.1mm dial gauge)
49. Precision square(90x 80mm)
50. Knife type straight edge(180mm)
51. Surface board(200 x 150 x 40mm)
52. Clearance gauge
53. Block gauge(Gr.2, 76 sheets a set)
54. G-sensor
55. Diamond forming grindstone forming device
56. Air spindle
57. Air dryer
58. Oil controller
59. 3-Point Dresser
60. V Shaped Wheel Radius Dresser
61. Universal Twin Rotary Dresser
62. Optiderss E
63. O.D. Grinding Attachment O.D.= Outside Diameter

*:When setting an option, ON-OFF switch is attached as an accessory.
**:When setting an option, ON-OFF switch and wet cover are attached as accessories.

Contact Us

Mitsui High-tec, Inc.

2-10-1, Komine,Yahatanishi-ku,Kitakyushu-shi,Fukuoka, 807-8588, Japan
TEL
+81-93-614-1142
Facsimile
+81-93-614-1202
Inquiries from the Internet
Contact Technology