Option

MSG Series Option List

Magnet / Chuck control
1.	Tilting electromagnetic chuck(250 x 120mm)
2.	Tilting electromagnetic chuck(300 x 120mm)
3.	Water-cooled tilting electromagnetic chuck (250 x 120mm)
4.	Water-cooled tilting electromagnetic chuck (300 x 120mm)
5.	Sine bar type electromagnetic chuck (240 x 125mm)
6.	Sine bar type electromagnetic chuck (270 x 125mm)
7.	Water-cooled sine bar electromagnetic chuck (240 x 125mm)
8.	Water-cooled sine bar electromagnetic chuck (270 x 125mm)
9.	Permanent sine bar chuck(240 x 125mm)
10.	Permanent sine bar chuck(270 x 125mm)
11.	Angular electromagnetic chuck(300 x 150mm)
12.	Angular electromagnetic chuck(400 x 200mm)
13.	Angular electromagnetic chuck(600 x 300mm)
14.	Angular electromagnetic chuck(700 x 400mm)
15.	Angular electromagnetic chuck(800 x 400mm)
16.	Water-cooled angular electromagnetic chuck (300 x 150mm)
17.	Water-cooled angular electromagnetic chuck (400 x 200mm)
18.	Reversible switch
19.	Manual controller
20.	Mitsui Automatic chuck control MAG-81 (Max. x 0.5A)
21.	Mitsui Automatic chuck control MAG-81A(Max. x 0.5A)
22.	Mitsui Automatic chuck control MAG-300HP(Max. x 2.5A)
23.	Cooling unit for water-cooled chuck
24.	Demagnetizer (AC100V1A)

(Note) Type of suitable chuck differs depending on the type of objective machine.

Dust-collecting and water-supplying equipment
25.	Dust catcher*
26.	Water-feeding unit **
27.	Hood port
28.	Dust catcher-water feeder
29.	Dust catcher-water feeder with 10[I] magnetic separator
30.	Water-feeding unit with 20[I] magnetic separator
31.	Water-feeding unit with 20[I] paper filter
32.	Sealing wet cover

Forming equipment
33.	R-forming device
34.	Angle-forming device
35.	Top face parallel dresser
36.	Diamond wheel dresser
37.	Sine bar(100mm)
38.	Balance bar
39.	Balance table
40.	V-block (Max. 25Φclamp)
41.	Master plate
42.	Square block(80 x 60 x 40mm)
43.	Square block(70 x 50 x 30mm)RB-753
44.	Square vice
45.	Sine bar type square vice
46.	Double-face dresser
47.	Side dresser
48.	Flange
49.	Forming pointer(0.3R.1.0ct)
50.	Diamond tool(1.0ct)
51.	Diamond tool(0.5ct)
52.	Special flange for small diameter grinding stone
53.	Dial gauge stand (with 0.1mm dial gauge)
54.	Precision square(90x 80mm)
55.	Knife type straight edge(180mm)
56.	Surface board(200 x 150 x 40mm)
57.	Clearance gauge
58.	Block gauge(Gr.2, 76 sheets a set)
59.	G-sensor
60.	Optical dressing grindstone forming device
61.	Projector scope
62.	Diamond forming grindstone forming device
63.	Air spindle
64.	Air dryer
65.	Oil controller

*:When setting an option, ON-OFF switch is attached as an accessory.

**:When setting an option, ON-OFF switch and wet cover are attached as accessories.

Others
Magnet scale / Digital reader	Parallel dresser	Grindstone balancer
Extremely easy modular system, capable of unit display switch-over for 0.5µ, 1µ and 10µ	Capable of dressing the grindstone without detaching the work on chuck and without moving the head up and down. Possible to attach easily using a tap hole on the head. Cutting scale is in 0.01mm graduations.	To attain a complete finished surface and extend the service life of spindle, it is necessary to keep the grindstone in balance.